![]() You could also use peel and stick tile to cover other surfaces throughout your home. You can create a peel and stick backsplash in your kitchen (one of the most common uses for Smart Tiles). Consider applying the sealant to any spots where the tile meets the floor, ceiling, counter, cupboards, or other surfaces.īest Places for Smart Tiles Where should you use Smart Tiles? Apply a small amount, following the guidelines on the caulk packaging. Match the sealant to the color backing on the tile or use clear. But if you want a polished, professional look, you can use silicone caulk sealant to fill in the seams and finish the top and bottom of the tile. Step 6: Apply Sealant, If DesiredĪfter sticking the tile to the wall, you are essentially done with your peel and stick tile installation. Occasionally step back and assess the tile application to ensure that it’s giving you the look you want. The process doesn’t take a long time, but you’ll want to give yourself permission to go slowly. If your tile has a pattern, be sure that it aligns correctly. Smooth the tile down, applying light pressure as you go. You’ll align the adhesive portion of the tile with your guidelines on the wall. Once you’re ready to put up your tile pieces, you simply fold back the protective paper backing and peel it away from the tile. Step 5: Peel and Stick the Smart Tile to the Wall Of course, it's best to do all the cutting on a flat surface. Because the peel and stick tiles are typically made with vinyl, you can use a ruler and a box cutter or utility knife to cut out the shapes you've planned. ![]() Remember, "measure twice, cut once" before cutting the tiles. Ensure that you have enough material to cover the area of the wall. Use a level, ruler, and chalk or marking pencil to trace guidelines for laying out your Smart tile. Then, line the tiles up against the wall and plan around any outlets, corners, or areas of the wall that you may need to accommodate. Step 3: Plan Smart Tile Placement and Measureīefore peeling and sticking the tile to the wall, you’ll want to plan the placement and lay out the tile (while the adhesive backing is still covered). Be sure to dry the wall thoroughly before installing peel and stick tile. Use a cleaner with a degreaser and cleaning rags to wash and remove all debris from the wall. It's essential to make sure there's no grease on the walls if you're working in a kitchen-the grease can cause the tiles to fail to adhere. One of the most crucial steps to peel and stick tile success is to start with a prepared surface. Step 2: Prepare the Wall for Peel and Stick Tile Although peel and stick isn't messy, you'll want room to measure, cut, and install the tile properly. Make sure you have a clean, clear workspace to begin your tile installation. ![]() ![]() Gather all the supplies and prepare the area ahead of time. Measure the wall space to ensure you purchase enough tiles to cover the area. Above all, make sure to check the manufacturer’s recommendations, as not all stick-on tile adhesives bond well with other glue.Before you begin your Smart tile installation, you’ll want to decide where you want the tiles to go. As Collier explains, “Applying permanent adhesion is an easy hack to add longevity to the tiles.” If you do choose to add additional glue, make sure to use a tile-specific adhesive such as Roberts 2057, and avoid glues like Liquid Nails that are not intended for installations. Though they’re a great option for those less “grounded” in their living spaces, most peel-and-stick floor tiles can easily last for decades, so don’t rule them out for long-term use. Any residual adhesive should be easy to tackle with a floor scraper, though it doesn’t hurt to have a remover like Goof Off on hand just in case. Begin by running a hair dryer across each tile to soften the adhesive, then slowly pull up each one, starting with the corners, using a putty knife if needed. If you change your mind about your tile or need to move on, peel-and-stick tile is just as easy to remove as to apply. Then walk on your new floor with a spring in your step. Keep a utility knife on hand to cut tiles (from the back) when needed to fit your space. Press the tiles down firmly and wipe away any residual adhesive as you go. After that? Peel-and-stick, like stir-fry, is all in the name. Some experts suggest marking your floor into quadrants to better strategize your attack. Remove any floor-level moldings so you can lay your tile flush with the baseboards.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |